Abstract

A single-port uniplanar antenna with a built-in tunable filter is presented for operation in multiple LTE bands for cognitive femtocell applications. The antenna is based on a monopole microstrip patch fed by coplanar waveguide. The frequency reconfigurability is achieved by using two PIN diodes to couple or decouple a ring slot resonator filter from the antenna feed line. By switching the PIN diodes, the proposed design can operate in either wideband or narrowband modes. When the antenna operates in the narrowband state, two varactor diodes are used to continuously tune the narrowband frequency from 2.55 to 3.2 GHz, while the wideband state is obtained over the 1.35–6.2 GHz band. The diodes and their biasing networks have nearly no severe effect on the antenna characteristics. Prototypes of the proposed structure using ideal and real switches, with and without varactors, are fabricated and tested. Measured and simulated results are in good agreement, thus verifying the good performance of the proposed design. The obtained results show that the proposed antenna is very suitable for cognitive radio applications, in which the wideband mode is used for spectrum sensing and the narrowband mode for transmission at different frequency bands.

1. Introduction

Recently, a “data tsunami” has resulted from the emergence of data-hungry wireless applications. Besides, the exponential growth in the number of smartphones and various portable devices has fueled the explosion of data traffic. In order to support higher throughput and better user satisfaction, the Long Term Evolution (LTE) standard has been proposed [1]. Moreover, in the most recent surveys [2, 3], it has been found that, in the near future, more than 60% of voice calls and 90% of data traffic will be originated from inside buildings. However, the traditional base stations have the reputation of poor indoor coverage due to the multipath and penetration losses [4, 5]. Furthermore, the LTE system operates at higher frequencies when the attenuation is highly significant. This severely reduces the network capacity and coverage in dense areas. Hence, it is important to find an alternative solution to improve the coverage and data rate in indoor environments, especially at higher frequencies.

Femtocells are considered as a promising solution not only to overcome the indoor coverage issue but also to achieve higher data rates by shorting the communication range and a better frequency reuse capability [6, 7]. Frequency reuse is a practical solution to overcome the spectrum scarcity [8], which is due principally to the increasing demand for more bandwidth versus the fact that all frequency bands are already allocated by the Federal Communications Commission (FCC). Another promising technology to meet the high data rate requirements and overcome the frequency scarcity is the cognitive radio (CR) paradigm [9]. It is able to continuously supervise the RF spectrum, in order to detect the spectrum holes, so-called white spaces, and, then, dynamically tune its characteristics to operate within these unused frequency bands [10]. By harnessing the advantages of these two technologies, cognitive femtocell base stations provide new opportunities for the next generation wireless networks, especially for LTE networks, to achieve high-quality service, maximize the efficiency of spectrum usage, and improve indoor coverage [11, 12].

The RF front-end of such systems must ensure their fundamental functions, which are the sensing and communication tasks [13]. Therefore, the reconfigurable antennas are the most suitable to meet these requirements [14], since they can ensure spectrum sensing by acting as an omnidirectional ultra-wideband (UWB) antenna and as a tunable narrowband antenna for communicating [1517]. In order to reduce the hardware complexity and cost, research communities are working toward moving some components and integrating them into another to create a more compact and less expensive system. To this end, it is suggested to combine the frequency-selective filter and the antenna into a single structure so as to achieve a so-called filtering antenna or “filtenna.” The filtenna is a planar antenna with a built-in bandpass filter, which can be used to provide frequency agility for communicating at different frequencies, without causing any interference to the adjacent bands and also to avoid undesired frequencies when it is used as a receiver. Despite many concurrent designs available for filtennas [15, 1822], the reconfigurable filtennas are rarely reported.

In this paper, the design of a new reconfigurable and tunable filtenna, by using a tunable bandpass filter based on ring slot resonator (RSR), is proposed for cognitive femtocell base stations. UWB to narrowband reconfiguration is achieved by employing two PIN diodes that couple or decouple the RSR filter from the antenna feed line, thereby making the filtenna work either in sensing or communication modes. When the filtenna is in the communication mode, the narrowband frequency tunability is attained by integrating two varactor diodes into the RSR filter. The frequency tunability is achieved to make the proposed filtenna communicate at different frequency bands. The most distinguishing feature of the proposed filtenna can be summarized in the fact that the tunable filter, which is part of the antenna design, provides frequency and bandwidth reconfigurability without affecting the radiation characteristics of the antenna. Moreover, the filtenna has a simple topology which makes it easy to be scaled to higher or lower frequencies. In addition, compared to [15, 1829], the proposed filtenna can achieve a continuous frequency tuning and UWB to narrowband reconfiguration by using only two PIN and two varactor diodes, thus simplifying and making a more flexible design. Measured results show a very wide impedance bandwidth from 1.3 GHz to more than 6 GHz, which fully covers LTE bands 1/2/7/33-41, while the narrowband frequency can realize a continuous frequency tuning from 2.55 to 3.2 GHz, covering the LTE bands 7/38/40/41. To the best of the authors’ knowledge, no femtocell-based cognitive single-port filtenna design using a simple filter and incorporating frequency reconfigurability and tunability has been published.

In Table 1, the performance of the proposed filtenna is compared with those of recently published papers. It is clearly observed that the proposed filtenna has more narrowband states and wide bandwidth for sensing state with only two PIN and varactor diodes than any of the reported designs. Moreover, the size of the proposed structure is smaller than the other designs based on their lower operating frequency.

2. Ring Slot Resonator Filter Design

In principle, the quarter-wavelength open-circuited stub presents a stopband response at the calculated frequency. Thus, by cascading two quarter-wavelength open-circuited stubs, calculated at two different frequencies, a bandpass filter can be obtained at the center frequency. A single ring slot produces a stopband response since it is acting as an open-circuited circuit at the calculated frequency. However, by cascading two of them, a passband response can be produced at the center frequency. Because of space constraints, a single ring slot can produce a passband response by bridging the slot at an appropriate location, which creates two short-circuited stubs.

To understand the ring slot mechanism, the simple and bridged slot configurations shown in Figures 1(a) and 1(b), respectively, were investigated. The simple ring slot is acting as a bandstop, when its average perimeter,  mm, is equal to a half-wavelength at the stopped frequency 2.4 GHz, as shown in Figure 2(a). However, when the slot is bridged, as shown in Figure 2(b), two short-circuited stubs in series that have different lengths  mm and  mm are created, which represent a stopband response at the corresponding quart-wavelength at 1.5 and 4 GHz, respectively, as shown in Figure 2(b). Consequently, the bridged slot ring configuration produces a passband response at the center frequency 2.4 GHz.

3. Sensing Antenna Design

As aforementioned, the sensing task is ensured by a UWB omnidirectional antenna. The initial design was started with the configuration shown in Figure 3.

The basic structure of the proposed filtenna is based on a wideband monopole antenna operating from 1.33 to 6.5 GHz, based on 10 dB return loss level, which is 132% around the center frequency 3.9 GHz. It consists of a monopole antenna fed by CPW line and designed on the same side of the substrate as the ground plane. A 1.58 mm thick FR4 substrate, with dielectric constant of 4.3 and , is used in this work. The dimensions of the basic UWB antenna and the CPW line are listed in Table 2, which are calculated using equations provided in [28, 29]. The photograph of the fabricated UWB antenna prototype as well as the simulated and measured return loss results are illustrated in Figure 4.

To choose the appropriate location to integrate the filter into UWB sensing antenna, the surface current distribution on the UWB antenna at 4 GHz is simulated, as shown in Figure 5. It can be clearly observed that the edges of the CPW line and the tapered slots have high current density. This suggests that this region is acting as a transmission part while the rest of monopole antenna is acting as a radiating part. The transmission region can thus be effectively utilized to integrate the RSR filter for an efficient filtering. The basic topologies of the RSR filter and the UWB antenna are now described.

4. Filtenna Fabrication and Measurements

4.1. Wide to Narrow Bandwidth Reconfiguration

After designing the UWB sensing antenna and choosing the final configuration of the RSR filter providing a bandpass response at 2.4 GHz, both structures are combined in a single structure to get the final filtenna, as shown in Figure 6(a). To examine the effect of the RSR filter on the antenna, an ideal switch is used. The OFF state is indicated by a gap while the ON state is represented by a metal pad. The aim of using ideal switches, in the first place, is to show the effect of active components (PIN diodes and their biasing networks) on the antenna characteristics. The RSR filter is located in the middle of the ground plane to avoid both the SMA connector and the strong coupling from the radiating part.

Figure 6(b) shows the antenna behavior when the filter is coupled and decoupled. As it can be noticed, the bandwidth reconfigurability is achieved. When the filter is decoupled from the antenna feed line (ON state), the filtenna acts as a UWB sensing antenna. The measured 10 dB impedance bandwidth covers the range from 1.3 to 6.6 GHz, which is 134% around the center frequency 3.95 GHz. However, when the filter is coupled to the antenna feed line through the gaps (OFF state), the filtenna carries out the communication task at 2.4 GHz, by switching from wide to narrow bandwidth. To further understand the filter mechanism, the surface current distributions for the narrowband mode are simulated at the operating frequency 2.4 GHz and at out-of-band frequencies 1 and 4 GHz, as shown in Figure 7. It is observed that the RSR filter passes the current at 2.4 GHz while reducing the current density on the antenna radiating element at the other frequencies.

The ideal switches reduce the computation time and have low insertion loss, but they do not provide fast and smooth switching, which are highly required in CR systems. Therefore, a real switch based on PIN diode is used instead. In this work, Infineon PIN diodes, model BAR88-02V, are used. According to their data sheet [30], for simulation purposes, the diode can be modeled as a 2.5 Ω resistor for the ON state and a parallel circuit of a 0.4 pF capacitor and a 65 kΩ resistor for the OFF state, as shown in Figure 8. Two PIN diodes are implemented in each gap of the RSR filter to decouple and couple it to the antenna. For experimental purposes, a gap of 0.8 mm is created to prevent the DC current from flowing directly to the ground plane. However, the RF continuity is maintained by bridging the gap with 22 pF surface mount device (SMD) capacitors. In order to protect the DC source from the RF signal, two high-impedance DC lines were printed on either side of the filtenna and connected to the ground plane via 33 nH SMD inductors, as shown in Figure 9.

Based on the aforementioned analysis, a prototype of the proposed filtenna is fabricated using LPKF milling machine to validate the circuit concept, as shown in Figure 10(a). The measurements were performed using an Anritsu MS2028C Vector Network. The simulated and measured return loss results for both states are illustrated in Figure 10(b). UWB sensing operation is achieved over the 1.25–6.2 GHz band, with good agreement observed between the simulated and measured results. The narrowband response is obtained at 2.45 GHz, corresponding to LTE band 38, with a slight discrepancy between the two curves, especially at higher frequencies. This can be understood by considering the high insertion loss of diodes as the frequency is increased. Besides, the manufacturing tolerances and the parasitic associated with the diode package and bias components may considerably contribute to the frequency shifting. Furthermore, it is observed that, by using real switches, the measured resonance is shifted from 2.43 to 2.45 GHz compared to ideal switches.

Moreover, to analyze the effect of PIN diodes on the antenna gain, a comparison between the ideal and real switches configurations is made in Table 3. It can be clearly observed that the measured gain in sensing mode is lower than in the communication mode. This result is principally attributed to the nature of the communication operation in providing a high gain on the signal-of-interest for maintaining a robust link between users in CR networks. On the other hand, the structure with ideal switches has up to 1.49 dB higher gain than the one with the real switches. This can be explained by the loss of the PIN diode switches and their biasing components, which is related to their internal resistances.

4.2. Narrowband Frequency Tunability

As previously mentioned, the communication task is achieved at one frequency. To achieve the frequency tunability of the narrowband operation, the bridges are replaced by varactor diodes. The varactor diode is placed in the bridge position to vary the ring slot effective length and thereby effectively tune the passband center frequency. Two BB145 varactor diodes from NXP Semiconductors [31], whose capacitance can be tuned in the range of 2.55–7.2 pF for a corresponding supply voltage of 4 to 1 V, are placed in each ring slot at the bridge location, as shown in Figure 11. An equivalent circuit used to model the diode in simulations is illustrated in Figure 12. Since the structure contains PIN and varactor diodes, their biasing circuits must thus be properly designed and separated to not negatively affect each other. The varactors biasing network is similar to that of the PIN diodes, with DC blocks of 22 pF and RF chokes of 33 nH. In addition, two RF chokes are introduced in each slot to preserve the DC current continuity to ground, as illustrated in Figure 11. The photograph of the final prototype is depicted in Figure 13(a). A GW Instek AFG-2112 DC power supply unit is used to provide constant and variable DC bias voltage for PIN and varactor diodes, respectively.

The simulated and measured return loss results for different varactor capacitance values are given in Figures 13(b) and 13(c), respectively. It is observed that, by varying the varactor voltages from 1 to 4 V (i.e., by decreasing the capacitance value from 7.2 to 2.5 pF), the operating frequency can be continuously tuned from 2.55 to 3.2 GHz, corresponding to a 1.26 tuning ratio. These bands include LTE bands 7 (2.5–2.57 GHz), 38 (2.57–2.62 GHz), 40 (2.3–2.4 GHz), and 41 (2.496–2.69 GHz), while the simulated tuning range is from 2.6 to 3.4 GHz, with a reasonably good agreement with experimental results. The slight discrepancies between experimental and simulation results would be mainly attributed to the inaccuracies of manufacturing, FR4 relative permittivity, bias voltage control error, and the lack of proper modeling of the discrete components in simulations. Moreover, a slight error can be introduced during the soldering of the SMD components and SMA connector which is not considered in simulations.

As explained earlier, the varactors are mainly used to tune the narrowband frequency, but their impact on sensing operation must be taken into consideration. The measured return losses for two varactor capacitance values, when the PIN diodes are set to ON, are plotted in Figure 14. It can be seen that the return loss remains nearly unchanged over the UWB sensing impedance bandwidth. Nevertheless, a slight variation can be observed at higher frequencies, but this change is negligible since the 10-dB impedance bandwidth remains unchanged. This can be explained by the fact that the variation of the capacitance value on the ground plane results in the change of the effective electrical length of the antenna and thereby slightly shifted its operating bandwidth. The effects of changing the varactor capacitance on the gain are investigated as well, in order to make sure that tuning frequency does not affect the radiation characteristics of the proposed filtenna. The realized gain is compared for different varactor capacitance values, when the filtenna works in communication mode (when PIN diodes are OFF), as shown in Figure 15. It can be observed that the gain varies from 2.2 to 5.6 dBi, with a maximum gain at the operating frequency of each biasing voltage. The effect of the RSR filter is clearly observed in the gain variations, which indicates that the filtenna when operating in the communication mode is filtering the unwanted frequencies. However, the varactor diodes have nearly no severe impact neither on the sensing characteristics nor on the realized gain of the filtenna.

The radiation efficiency of the prototype in both modes is also measured using the Wheeler cap method [32] and compared in Figure 16. This method is very simple conceptually. It requires one measurement of the impedance with the antenna in free space and another where the antenna is enclosed with a small metallic cap placed at a distance greater than λ/2π [33]. The real part of the first impedance measurement is equivalent to the loss resistance of the antenna , while the real part of the second measurement includes the radiation resistance and loss resistance . By using (1), the radiation efficiency can be calculated. From Figure 16, it is seen that the radiation efficiency is found to be better than 69% in the wideband mode. In the narrowband mode, the efficiency is found to be better than 79%. The difference between the two curves is because of the forward resistance of the PIN diodes when they are on which contribute to thermal losses:

The radiation patterns of the proposed filtenna for both modes are shown in Figure 17. For the sensing state, the patterns are plotted at 1.5, 3.5, and 5 GHz, while for the narrowband state, they are plotted at the resonant frequency of the communication mode. It can be noticed that the radiation patterns of sensing mode are slightly omnidirectional throughout the operating bandwidth with low cross-polarization level, which is better than 20 dB over the main beam direction. However, it can also be seen that the narrowband mode exhibits a quasi-doughnut shape with slightly lower cross-polarization levels, especially in the Y-Z plane. This is mainly because, at higher frequencies, the effective electrical length of the ground plane is much longer than one wavelength, which leads to splitting the radiation pattern.

5. Conclusion

An electronically reconfigurable and tunable filtenna for cognitive femtocell base stations has been presented. The basic design of the filtenna consists of monopole antenna fed by CPW with a built-in RSR filter in the ground plane. To switch the filtenna between the sensing mode and the communication mode, two PIN diodes are used to couple or decouple the RSR filter from the antenna feed line. However, in order to continuously tune the resonant frequency of the communication mode, two varactor diodes are used to change the effective electrical length of the filter slots. Four filtenna prototypes have been manufactured and tested to verify the design concept. Each prototype could be regarded as an evolution of the previous prototype. Measured results have shown that the proposed filtenna provides an impedance bandwidth from 1.35 to 6.2 GHz and 2.33 to 3.1 GHz in sensing and communication modes, respectively, given a very wide bandwidth tuning ratio of 6.3 : 1. Moreover, the resonant frequency of the communication mode can be continuously tuned from 2.55 to 3.2 GHz, by varying the DC bias voltage from 1 to 4 V, respectively, corresponding to a 1.26 frequency tuning ratio. Therefore the proposed design is expected to fully cover the LTE bands 1/2/7/33-41. In addition, the gain, the radiation efficiency, and the radiation patterns show that the frequency tuning and reconfiguration mechanisms are accomplished without affecting the filtenna characteristics, qualifying the proposed design for use in many CR applications.

Competing Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

The authors are grateful to Departamento de Ingenieria de Comunicaciones, University of Cantabria (UNICAN), Spain, for support with regard to simulation software and facilities.