Removal of Zinc from Aqueous Solution by Optimized Oil Palm Empty Fruit Bunches Biochar as Low Cost Adsorbent

Zamani, Seyed Ali; Yunus, Robiah; Samsuri, A. W.; Salleh, M. A. Mohd; Asady, Bahareh

doi:https://doi.org/10.1155/2017/7914714

Bioinorganic Chemistry and Applications

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusion Conflicts of Interest References Copyright Related Articles

Special Issue

Metals in the Environment: Toxic Metals Removal

View this Special Issue

Research Article | Open Access

Volume 2017 | Article ID 7914714 | https://doi.org/10.1155/2017/7914714

Removal of Zinc from Aqueous Solution by Optimized Oil Palm Empty Fruit Bunches Biochar as Low Cost Adsorbent

Seyed Ali Zamani,¹Robiah Yunus,²A. W. Samsuri,³M. A. Mohd Salleh,⁴and Bahareh Asady²

Academic Editor: Muataz A. Atieh

Received05 Jan 2017

Accepted19 Feb 2017

Published21 Mar 2017

Abstract

This study aims to produce optimized biochar from oil palm empty fruit bunches (OPEFB), as a green, low cost adsorbent for uptake of zinc from aqueous solution. The impact of pyrolysis conditions, namely, highest treatment temperature (HTT), heating rate (HR), and residence time (RT) on biochar yield and adsorption capacity towards zinc, was investigated. Mathematical modeling and optimization of independent variables were performed employing response surface methodology (RSM). HTT was found to be the most influential variable, followed by residence time and heating rate. Based on the central composite design (CCD), two quadratic models were developed to correlate three independent variables to responses. The optimum production condition for OPEFB biochar was found as follows: HTT of 615°C, HR of 8°C/min, and RT of 128 minutes. The optimum biochar showed 15.18 mg/g adsorption capacity for zinc and 25.49% of yield which was in agreement with the predicted values, satisfactory. Results of the characterization of optimum product illustrated well-developed BET surface area and porous structure in optimum product which favored its sorptive ability.

1. Introduction

Heavy metal pollution is one of the most serious environmental issues, faced worldwide today [1–3]. Intense industrial activities result in releasing of significant amount of heavy metals including zinc into aqua environment [4]. Mining, metal coating, galvanizing steel and iron, and production of batteries, as well as production of deodorants, paints, ceramic, wood, drug, and fabrics, are major industries, responsible for releasing of zinc into environment [4]. Human exposure to intense amount of zinc leads to metal-fume fever, vomiting, stomach cramp, nausea, loss of appetite, and neurological signs such as ataxia [5]. Health risks of zinc contaminated water for both human and other living organisms is a great concern because of its non biodegradability and mobility. According to World Health Organization guidelines for quality of drinking water and to protect the environment, maximum acceptable zinc level in drinking water is recommended as 5.00 mg/l [6]. Due to global shortage of water resources, health risks, and environmental problems associated with heavy metal pollution such as zinc, treatment of wastewater by effective methods is critical.

Different methods and techniques have been introduced for controlling water and wastewater pollution by heavy metals such as ion exchange, adsorption, precipitation, coagulation, membrane technologies, and reverse osmosis. Among these methodologies, adsorption has been demonstrated to be an economically practicable alternative method for uptake of metals from water system [7, 8]. The simplicity of operation and design in this method as well as its effectiveness in minimizing various types of pollutants leads to its widespread applicability in controlling water pollution [9]. High cost of adsorption by commercially produced activated carbon leads to extensive researches on possibility of using waste biomaterials, as low cost sorbents, for treatment of water and wastewater from heavy metal contaminants [10].

In recent years, biochar from different agrobased and municipal waste materials has been shown to be a potential low cost alternative for separation of heavy metal from water system [11, 12]. Different agrobased and municipal wastes derived biochars have been evaluated for removal of toxic metals in numerous studies. The results of these studies highlighted the capability of biochars as great potential low cost sorbents and indicated the important role of biochar’s physiochemical characteristics in its uptake ability [2, 7, 13–16].

Annually, enormous amounts of biowastes from oil palm mills are produced around the world which contribute to great environmental concern, and many researchers have been focused on conversion of these wastes into value-added products. Oil palm empty fruit bunches account for 23% per ton of fresh fruit bunch which should be handled properly [17]. Currently, the majority of empty fruit bunches are combusted in the incinerators for the purpose of fertilizer production which produces “white smoke” and considered an environmental concern by the Department of Environment [18]. The great amount of generated empty fruit bunches from oil palm mills could be a potential feedstock substrate for biochar production by an environmentally friendly method. Production of biochar from oil palm empty fruit bunches, an abundant waste of oil palm mill, has twofold advantage: firstly, production of low cost and ecofriendly adsorbent for removal of heavy metals and, secondly, solving part of waste disposal problem by conversion of unwanted wastes into value-added products.

Production of efficient sorbent for this purpose has been always a concern. Among the sorbent characteristics, surface area, surface functionalities, and acceptable level of yield are important in adsorption process design [19]. These characteristics of biochar are controlled by its production conditions and primary feedstock properties [19]. In assessing the effect of production conditions, employing an adequate experimental design is key point.

Design of experiment (DOE) enables engineering researchers to alleviate the costs by rationalizing the experiments and improving productivity and product quality. Response surface methodology, one of the DOE techniques, is applied for experimental design, statistical modeling, and optimization of a process. It is a helpful tool in studying the effect of factors and their interactions on specific response to optimize the response of interest [20].

RSM has been widely used in optimization of experimental conditions of various processes; however, its application in production of biochar is very rare in literature. Some previous studies focused on applying RSM in determining the effect of different parameters during production of adsorbent and batch adsorption experiments, on removal of hazardous contaminants such as chromium [21, 22], copper [23], nickel [24], reactive blue dye [25], lead and zinc [26], and cationic and anionic dye [27].

To our knowledge, no study has been performed on optimized production of biochar from oil palm empty fruit bunches, applying RSM. Therefore, the focus of the present study is to produce biochar from oil palm empty fruit bunches and to optimize the preparation conditions using central composite design for yield and its adsorption capacity towards zinc. The influence of three numerical variables, namely, highest treatment temperature, heating rate, and residence time, on the responses was considered, simultaneously.

2. Materials and Methods

2.1. Preparation of Biochar

Oil palm empty fruit bunches were collected from Ulu Langat Palm Oil Mill, a local oil palm mill in Malaysia; Seri Sdn Bhd (Lot 3115, Batu 34, Jalan Banting, Dengkil, 43800, Selangor, Malaysia). The biomass samples were dried in oven at 105°C for 24 h to get constant weight. Afterward, the samples were cut into smaller parts (2 nm) to ease the pyrolysis process. The pyrolysis process was performed by placing samples in vertical stainless steel reactor and heating from room temperature to predetermined temperature with specific heating rate and they were kept at highest temperature for specific duration. Purified nitrogen (99.995%) with flow rate of 150 cm³/min was used during pyrolysis process to wash tarry vapors away from the surface of biochar.

2.2. Design of Experiment

Response surface methodology (RSM) is a statistical technique which utilizes the quantitative data of the experiments for purpose of determining the regression model and optimum operation conditions [28]. It applies mathematical and statistical methods for analyzing and simulating of a process with the objective of optimizing a response which is affected by several independent variables [29]. Central composite design (CCD) is the most common method for fitting quadratic surfaces and optimization with minimum number of experiments [30]. In general, CCD consists of factorial runs, axial runs, and center points in which is the number factors.

Three numerical factors have been considered for this purpose, namely, as highest treatment temperature (HTT), as heating rate (HR), and as residence time (RT). Two responses in this work were yield () and adsorption capacity of OPEFB biochar (). Number of runs based on CCD method for three independent variables is equal to 20 experiments, including 8 factorial points, 6 axial points, and 6 center points based on the following equation [31]:where is the total number of experiments and is the number of factors. The center points are useful in considering the errors of experiments and reproducibility of the model. For all three factors the ranges have been entered based on “−alpha” and “+alpha” level where alpha is the distance of axial points from center points, intending not to have any unreachable level for the factors. These variables and their respective ranges were selected based on screening tests in preliminary studies. Levels of independent variables are given in Table 1. The experiments were conducted as randomized in order to minimize the influence of uncontrolled factors. An empirical model was developed to correlate the three independent variables and each response based on second-order polynomial equation as follows:

In which, is the constant, is the linear coefficient and is the quadratic coefficient, and and are the coded values of pyrolysis conditions.

2.3. Model Fitting and Statistical Analysis

The analysis of experimental data was performed using Design Expert version 7 (STAT-EASE Inc., Minneapolis, USA) for regression analysis to fit the empirical models and statistical significance evaluation of the models.

2.4. Adsorption Experiments

Zinc stock solution was prepared by dissolving appropriate amount of ZnCl₂ (Anhydrous, Sigma Aldrich) in Millipore water with purity of 99.99% to concentration of 2000 ppm. The batch adsorption experiments were conducted in 20 sets of 250 ml Erlenmeyer flasks. In a typical experiment, 0.4 g of biochar was added to 50 ml of heavy metal solution with concentration of 200 ppm and the pH of solution was set at 6. Subsequently the mixture was agitated for 24 hours for equilibration and then filtered employing Whatman filter paper. The equilibrium time was selected based on preliminary studies as the time when the zinc concentration remained constant. The resultant solution was analyzed for concentration of zinc utilizing A Analyst 400 PerkinElmer atomic absorption spectrometer device. The adsorption capacity of biochars was calculated by the following equation:

In the previous equation, and are the initial and equilibrium concentration of zinc (mg/l), respectively. (mg/g) is the adsorption capacity of biochar, is the dry mass of biochar (g), and is for volume of solution (l).

2.5. Yield of Biochar

The yield of biochar was calculated according to the following equation:

2.6. Characterization of Optimum Biochar

The surface structure of biochar was analyzed by means of scanning electron microscopy utilizing Zeiss scanning electron microscope (Carl Zeiss Germany). adsorption at 77 K was performed for surface area and pore volume estimation of biochar, using Sorptomatic 1990 system (Thermo Finnigan). Surface functional groups of biochars were determined with aid of Fourier Transform Infrared spectroscopy, using Nicolet Nexus 6700 FTIR spectrometer. The KBr pellet was prepared by mixing well grinded biochar samples with KBr powder at ratio of 1 : 100 approximately.

3. Results and Discussion

3.1. Development of Regression Model Equation

The complete design matrix of experiments with the obtained results for both responses is presented in Table 2. A polynomial regression equation was developed based on CCD to analyze the variables, their interactions, and identifying the significant factors. Runs 1, 4, 12, 15, 16, and 19 are center points and used to determine the error of experiments. Biochar yield was found to be in the range of 23.2% and 33.73% while the adsorption capacity for zinc obtained ranged between 7.59 mg/g and 14.74 mg/g.

Based on the sequential model sums of squares, the fitted model was chosen as the highest order polynomial model in which the additional terms were significant and model was not aliased. For both responses, the quadratic model was selected as suggested by the software. The final empirical equations for yield () and zinc adsorption capacity of biochar () in terms of coded variables are presented in (1) and (2), respectively.

Positive sign in front of the terms represents the synergistic influence while negative sign represents antagonistic influence. Values of coefficient determination, squared, adjusted squared, standard deviation (SD), and coefficient of variation (CV) were used to evaluate the quality of developed model. values for (5) and (6) were 0.9766 and 0.9794, implying that models were able to explain 97.66% and 97.94% of total variance in biochar yield and biochar adsorption capacity for zinc, respectively. The closer is to unity, the better the model fits experimental data. Both values are considered relatively high and suggesting satisfactory agreement between model and experimental data. The adjusted squared with values of 0.9556 and 0.9609 for (5) and (6), respectively, indicates good sample size and ability of model. Coefficient of variation (CV) is a measure of the model reproducibility and considered as the ratio of standard deviation to mean value of observed response. The model is regarded as reproducible if the value of CV for the model is less than 10% [26, 32]. Coefficients of variation (CV) for both studied responses were less than 10% and were equal to 2.04% and 3.47% for and , respectively. The standard deviation values for the models were 0.55 and 0.42 which reflect the accuracy of the model. The adequacy of the model was further checked by analysis of variance (ANOVA). The ANOVA for quadratic model for yield of biochar is given in Table 3. From ANOVA for yield of biochar, the -value was 46.44 and value was less than 0.0001, reflecting that model was significant. Regarding the model terms, value less than 0.05 implies that model term was significant. According to Table 3 for yield of biochar, , , , and were significant model terms, whereas , , , , and were insignificant terms to the model.

The result of ANOVA for quadratic model for adsorption capacity of biochar is presented in Table 4. The -value of 52.95 with value less than 0.0001 indicates the significance of the model. Table 4 illustrates that , , , , , and are significant model terms. On the other hand, the interactions of factors , , and were insignificant terms to the response.

The predicted versus experimental values for yield and adsorption capacity of OPEFB biochar are illustrated in Figures 1 and 2, respectively. As it can be observed, the predicted values are close to the experimental values which indicate that the developed model successfully fitted the correlation between variables and responses.

3.2. Yield of Oil Palm Empty Fruit Bunches Biochar (OPEFBB)

Referring to the yield of biochar, HTT had the greatest influence on the response followed by the HR and RT. Figures 3(a) and 3(b) represent the three-dimensional response surfaces to demonstrate the influence of biochar preparation conditions on yield. Figure 3(a) illustrates the surface plot of percentage of yield under the impact of highest treatment temperature (HTT) and heating rate (HR) where residence time (RT) was fixed at zero level (105 minutes). On the other hand, Figure 3(b) illustrates the effect of highest treatment temperature and residence time on yield (heating rate was fixed at zero level). As demonstrated in Figures 3(a) and 3(b), the biochar yield decreased with increasing in HTT, HT, and RT.

(a)

(b)

Similar trend was also reported in other works, studying the influence of production parameters on char yield. Al-Wabel et al. reported reduction in yield of Conocarpus wastes biochar by increasing the highest treatment temperature, specifically when the temperature increased more than 200°C. This may be due to the destruction of cellulose and hemicellulose and combustion of organic matters [33]. Angin found that the yield of safflower seed cake-based biochar was reduced by rising pyrolysis temperature and heating rate. The effect of heating rate on the yield was also reported to be more significant at lower pyrolysis temperatures [34]. McBeath et al. examined the effect of pyrolysis conditions on yield and characteristics of biochar from eighteen different feedstocks and concluded that increasing pyrolysis temperature resulted in lower yield of char [35]. This is due to the evaporation of volatile matters and higher heat and mass transfer rate and destructive reactions. In another study by Hmid et al. both pyrolysis temperature and heating rate were reported as influential factors on the yield of biochars derived from olive solid residues considerably [36]. Ronsse et al. studied the influence of pyrolysis peak temperature and residence time on the yield of biochars from various feedstocks. It was observed that biochar yield tends to decrease by increasing residence time and peak temperature [37].

In this work, all three production variables correlated negatively with biochar yield. The interaction effect of production parameters on biochar yield was not significant. The increase in pyrolysis temperature resulted in releasing of more volatile compound, primary decomposition of parent material, and possible secondary decomposition of produced biochar. Increasing in heating rate may cause severe heat and mass transfer rate which led to lower biochar yield. The influence of residence time on biochar yield was not also significant.

3.3. Adsorption Capacity of Oil Palm Empty Fruit Bunches Biochar (OPEFBB)

Based on the ANOVA, all three variables and their quadratic effect were found to be significant on the adsorption capacity of OPEFB biochar; however, HTT with -value of 33.4246 was the most influential factor. Figures 4(a) and 4(b) demonstrate the three-dimensional response surfaces to show the influence of operating variables on adsorption capacity. The effect of the highest treatment temperature and heating rate on adsorption capacity where residence time was maintained at zero level is depicted in Figure 4(a), whereas the effect of highest treatment temperature and residence time on adsorption capacity of OPEFB biochar when heating rate was fixed at zero level is presented in Figure 4(b). As it can be seen from Figure 4(a), the adsorption capacity of biochar increases with increasing temperature and heating rate up to specific point and, afterward, it decreases possibly because of blockage of some pores due to melting and releasing of tars. The highest treatment temperature had a positive linear effect on adsorption capacity, whereas heating rate has a negative effect. In addition, both factors have a negative quadratic effect on adsorption capacity of OPEFB biochar. Raising heating rate increases the adsorption capacity up to a certain point after which it reduces. This is due to the fact that the time for releasing volatiles becomes shortened at high heating rate which results in agglomeration of volatiles between and inside the pores and, therefore, the chance of blocking the pores entrance increases. Similar results have been reported in other studies [34, 38, 39].

(a)

(b)

Surface plot of the effect of highest treatment temperature and residence time on adsorption capacity of OPEFB biochar when heating rate was fixed at zero level is presented in Figure 4(b). Residence time increase favors the adsorption capacity up to a certain point of time, after which further increase causes the adsorption capacity to decrease due to the failure of pore walls’ strength and their destruction.

3.4. Process Optimization

Getting high yield is an important factor in producing biosorbents, but adsorption capacity determines the quality of product. Therefore, both high yield and high adsorption capacity is desirable for economics feasibility of the product. However, optimizing both of these responses is very difficult as their affecting factors are opposite, which means adsorption capacity of OPEFB biochar increases while the yield decreases and vice versa. Consequently, in order to compromise between the two responses, the function of desirability has been employed using Expert-Design software version 7 (STAT-EASE Inc., Minneapolis, USA). The experimental conditions which showed the highest desirability were chosen for verification. The yield and adsorption capacity of the biochar prepared under optimum conditions compared to the predicted values are presented in Table 5. The optimum biochar from oil palm empty fruit bunches was obtained using highest temperature of 615°C, heating rate of 8°C/min, and residence time of 128 min. The optimum biochar showed the adsorption capacity of 15.03 mg/g towards zinc and the biochar yield of 25.27%.

As it can be observed from Table 5, the obtained experimental results are in good agreement with model prediction points with relatively small deviation, indicating the accuracy of the model. Overall, OPEFB proved to be a potential promising substrate for production of biochar, a green low cost sorbent, with high performance for removal of heavy metals (zinc) from the aqueous solution.

3.5. Characterization

Figures 5(a) and 5(b) illustrate the scanning electron microscope images of the precursor (OPEFB) and the biochar obtained under optimum conditions. As it is clear in the micrograph, the external surfaces of the biochar obtained under optimized conditions consist of cracks, crevices, and significant amount of honey comb like pores with various sizes. Comparison of this micrograph with SEM micrograph of OPEFB revealed that during pyrolysis the cracks and pores of biochar become cleaner due to increase in devolatilization and, therefore, more ordered structural arrangement can be detected in optimum product.

(a)

(b)

Figure 6 displays the adsorption-desorption isotherm of OPEFB biochar synthesized under RSM optimum conditions. This adsorption isotherm can be classified as type I with a type H4 hysteresis loop at relative pressure 0.9, resembling microporous structured materials with some degree of mesoporosity. The surface physical parameters determined from adsorption isotherm for optimum product and OPEFB biochar synthesized at 300°C from the preliminary studies are summarized in Table 6. By comparison of the results of textural properties of optimum OPEFB biochar with unoptimized one, it is evident that RSM optimum product displays higher BET surface area, micropore surface area, micropore volume, and mesopore volume indicating pore development at optimum pyrolysis conditions. This is most likely due to the progressive decomposition of volatile matter and better carbonization that leads to enhanced porosity.

4. Conclusion

In this study, novel, low cost adsorbent from empty fruit bunches were synthesized by pyrolysis. The influence of pyrolysis conditions on the yield and adsorption capacity of oil palm empty fruit bunches biochar for zinc was studied employing RSM. Through analysis of developed response surfaces, HTT was found to have the most significant influence on both responses. The optimum biochar was obtained at highest treatment temperature of 615°C, heating rate of 8°C/min, and residence time of 128 min which demonstrated 15.18 mg/g zinc adsorption capacity and 25.49% yield. The resultant biochar produced under optimum conditions demonstrates 421.26 m²/g surface area and 0.15 cm³/g total pore volume.

Conflicts of Interest

Authors declare no conflicts of interest.

References

S.-J. Lee, J. H. Park, Y.-T. Ahn, and J. W. Chung, “Comparison of heavy metal adsorption by peat moss and peat moss-derived biochar produced under different carbonization conditions,” Water, Air, and Soil Pollution, vol. 226, no. 2, article 2275, 2015.
View at: Publisher Site | Google Scholar
D. Kołodyńska, J. Krukowska, and P. Thomas, “Comparison of sorption and desorption studies of heavy metal ions from biochar and commercial active carbon,” Chemical Engineering Journal, vol. 307, pp. 353–363, 2017.
View at: Publisher Site | Google Scholar
V. M. Martínez-Juárez, J. F. Cárdenas-González, M. E. Torre-Bouscoulet, and I. Acosta-Rodríguez, “Biosorption of mercury (II) from aqueous solutions onto fungal biomass,” Bioinorganic Chemistry and Applications, vol. 2012, Article ID 156190, 5 pages, 2012.
View at: Publisher Site | Google Scholar
S. Malamis and E. Katsou, “A review on zinc and nickel adsorption on natural and modified zeolite, bentonite and vermiculite: examination of process parameters, kinetics and isotherms,” Journal of Hazardous Materials, vol. 252-253, pp. 428–461, 2013.
View at: Publisher Site | Google Scholar
F. Fu and Q. Wang, “Removal of heavy metal ions from wastewaters: a review,” Journal of Environmental Management, vol. 92, no. 3, pp. 407–418, 2011.
View at: Publisher Site | Google Scholar
N. K. Srivastava and C. B. Majumder, “Novel biofiltration methods for the treatment of heavy metals from industrial wastewater,” Journal of Hazardous Materials, vol. 151, no. 1, pp. 1–8, 2008.
View at: Publisher Site | Google Scholar
D. Mohan, A. Sarswat, Y. S. Ok, and C. U. Pittman, “Organic and inorganic contaminants removal from water with biochar, a renewable, low cost and sustainable adsorbent—a critical review,” Bioresource Technology, vol. 160, pp. 191–202, 2014.
View at: Publisher Site | Google Scholar
F. Mutongo, O. Kuipa, and P. K. Kuipa, “Removal of Cr(VI) from aqueous solutions using powder of potato peelings as a low cost sorbent,” Bioinorganic Chemistry and Applications, vol. 2014, Article ID 973153, 2014.
View at: Publisher Site | Google Scholar
A. Bhatnagar and M. Sillanpää, “Utilization of agro-industrial and municipal waste materials as potential adsorbents for water treatment—a review,” Chemical Engineering Journal, vol. 157, no. 2-3, pp. 277–296, 2010.
View at: Publisher Site | Google Scholar
A. S. Singha and A. Guleria, “Use of low cost cellulosic biopolymer based adsorbent for the removal of toxic metal ions from the aqueous solution,” Separation Science and Technology, vol. 49, no. 16, pp. 2557–2567, 2014.
View at: Publisher Site | Google Scholar
X. Tan, Y. Liu, G. Zeng et al., “Application of biochar for the removal of pollutants from aqueous solutions,” Chemosphere, vol. 125, pp. 70–85, 2015.
View at: Publisher Site | Google Scholar
M. I. Inyang, B. Gao, Y. Yao et al., “A review of biochar as a low-cost adsorbent for aqueous heavy metal removal,” Critical Reviews in Environmental Science and Technology, vol. 46, no. 4, pp. 406–433, 2016.
View at: Publisher Site | Google Scholar
Y. Han, A. A. Boateng, P. X. Qi, I. M. Lima, and J. Chang, “Heavy metal and phenol adsorptive properties of biochars from pyrolyzed switchgrass and woody biomass in correlation with surface properties,” Journal of Environmental Management, vol. 118, pp. 196–204, 2013.
View at: Publisher Site | Google Scholar
J.-H. Park, Y. S. Ok, S.-H. Kim et al., “Competitive adsorption of heavy metals onto sesame straw biochar in aqueous solutions,” Chemosphere, vol. 142, pp. 77–83, 2016.
View at: Publisher Site | Google Scholar
X. Cui, S. Fang, Y. Yao et al., “Potential mechanisms of cadmium removal from aqueous solution by Canna indica derived biochar,” Science of the Total Environment, vol. 562, pp. 517–525, 2016.
View at: Publisher Site | Google Scholar
G. N. Paranavithana, K. Kawamoto, Y. Inoue et al., “Adsorption of Cd²⁺ and Pb²⁺ onto coconut shell biochar and biochar-mixed soil,” Environmental Earth Sciences, vol. 75, no. 6, article 484, 2016.
View at: Publisher Site | Google Scholar
R. Omar, A. Idris, R. Yunus, K. Khalid, and M. I. Aida Isma, “Characterization of empty fruit bunch for microwave-assisted pyrolysis,” Fuel, vol. 90, no. 4, pp. 1536–1544, 2011.
View at: Publisher Site | Google Scholar
S. H. Chang, “An overview of empty fruit bunch from oil palm as feedstock for bio-oil production,” Biomass and Bioenergy, vol. 62, pp. 174–181, 2014.
View at: Publisher Site | Google Scholar
T. Chen, Y. Zhang, H. Wang et al., “Influence of pyrolysis temperature on characteristics and heavy metal adsorptive performance of biochar derived from municipal sewage sludge,” Bioresource Technology, vol. 164, pp. 47–54, 2014.
View at: Publisher Site | Google Scholar
M. V. Gil, M. Martínez, S. García, F. Rubiera, J. J. Pis, and C. Pevida, “Response surface methodology as an efficient tool for optimizing carbon adsorbents for CO2 capture,” Fuel Processing Technology, vol. 106, pp. 55–61, 2013.
View at: Publisher Site | Google Scholar
J. Cao, Y. Wu, Y. Jin, P. Yilihan, and W. Huang, “Response surface methodology approach for optimization of the removal of chromium(VI) by NH2-MCM-41,” Journal of the Taiwan Institute of Chemical Engineers, vol. 45, no. 3, pp. 860–868, 2014.
View at: Publisher Site | Google Scholar
S. Bajpai, S. K. Gupta, A. Dey et al., “Application of Central Composite Design approach for removal of chromium (VI) from aqueous solution using weakly anionic resin: modeling, optimization, and study of interactive variables,” Journal of Hazardous Materials, vol. 227-228, pp. 436–444, 2012.
View at: Publisher Site | Google Scholar
Z. Z. Chowdhury, S. M. Zain, R. A. Khan, A. Arami-Niya, and K. Khalid, “Process variables optimization for preparation and characterization of novel adsorbent from lignocellulosic waste,” BioResources, vol. 7, no. 3, pp. 3732–3754, 2012.
View at: Google Scholar
A. Saravanan, P. Senthil Kumar, and B. Preetha, “Optimization of process parameters for the removal of chromium(VI) and nickel(II) from aqueous solutions by mixed biosorbents (custard apple seeds and Aspergillus niger) using response surface methodology,” Desalination and Water Treatment, vol. 57, no. 31, pp. 14530–14543, 2016.
View at: Publisher Site | Google Scholar
Z. Ayazi, Z. M. Khoshhesab, and S. Norouzi, “Modeling and optimizing of adsorption removal of Reactive Blue 19 on the magnetite/graphene oxide nanocomposite via response surface methodology,” Desalination and Water Treatment, vol. 57, no. 52, pp. 25301–25316, 2016.
View at: Publisher Site | Google Scholar
T. M. Alslaibi, I. Abustan, M. A. Ahmad, and A. A. Foul, “Application of response surface methodology (RSM) for optimization of Cu2+, Cd2+, Ni2+, Pb2+, Fe2+, and Zn2+ removal from aqueous solution using microwaved olive stone activated carbon,” Journal of Chemical Technology and Biotechnology, vol. 88, no. 12, pp. 2141–2151, 2013.
View at: Publisher Site | Google Scholar
M. Auta and B. H. Hameed, “Optimized waste tea activated carbon for adsorption of Methylene Blue and Acid Blue 29 dyes using response surface methodology,” Chemical Engineering Journal, vol. 175, no. 1, pp. 233–243, 2011.
View at: Publisher Site | Google Scholar
A. Witek-Krowiak, K. Chojnacka, D. Podstawczyk, A. Dawiec, and K. Pokomeda, “Application of response surface methodology and artificial neural network methods in modelling and optimization of biosorption process,” Bioresource Technology, vol. 160, pp. 150–160, 2014.
View at: Publisher Site | Google Scholar
D. C. Montgomery, Design and Analysis of Experiments, John Wiley & Sons, 2008.
D. Ranjan, D. Mishra, and S. H. Hasan, “Bioadsorption of arsenic: an artificial neural networks and response surface methodological approach,” Industrial and Engineering Chemistry Research, vol. 50, no. 17, pp. 9852–9863, 2011.
View at: Publisher Site | Google Scholar
J. M. Salman and B. H. Hameed, “Effect of preparation conditions of oil palm fronds activated carbon on adsorption of bentazon from aqueous solutions,” Journal of Hazardous Materials, vol. 175, no. 1–3, pp. 133–137, 2010.
View at: Publisher Site | Google Scholar
I. Y. S. Rustom, M. H. López‐Leiva, and B. M. Nair, “Optimization of extraction of peanut proteins with water by response surface methodology,” Journal of Food Science, vol. 56, no. 6, pp. 1660–1663, 1991.
View at: Publisher Site | Google Scholar
M. I. Al-Wabel, A. Al-Omran, A. H. El-Naggar, M. Nadeem, and A. R. A. Usman, “Pyrolysis temperature induced changes in characteristics and chemical composition of biochar produced from conocarpus wastes,” Bioresource Technology, vol. 131, pp. 374–379, 2013.
View at: Publisher Site | Google Scholar
D. Angin, “Effect of pyrolysis temperature and heating rate on biochar obtained from pyrolysis of safflower seed press cake,” Bioresource Technology, vol. 128, pp. 593–597, 2013.
View at: Publisher Site | Google Scholar
A. V. McBeath, C. M. Wurster, and M. I. Bird, “Influence of feedstock properties and pyrolysis conditions on biochar carbon stability as determined by hydrogen pyrolysis,” Biomass and Bioenergy, vol. 73, pp. 155–173, 2015.
View at: Publisher Site | Google Scholar
A. Hmid, D. Mondelli, S. Fiore, F. P. Fanizzi, Z. Al Chami, and S. Dumontet, “Production and characterization of biochar from three-phase olive mill waste through slow pyrolysis,” Biomass and Bioenergy, vol. 71, pp. 330–339, 2014.
View at: Publisher Site | Google Scholar
F. Ronsse, S. van Hecke, D. Dickinson, and W. Prins, “Production and characterization of slow pyrolysis biochar: influence of feedstock type and pyrolysis conditions,” GCB Bioenergy, vol. 5, no. 2, pp. 104–115, 2013.
View at: Publisher Site | Google Scholar
R. A. Brown, A. K. Kercher, T. H. Nguyen, D. C. Nagle, and W. P. Ball, “Production and characterization of synthetic wood chars for use as surrogates for natural sorbents,” Organic Geochemistry, vol. 37, no. 3, pp. 321–333, 2006.
View at: Publisher Site | Google Scholar
H. Yang, R. Yan, H. Chen, D. H. Lee, D. T. Liang, and C. Zheng, “Mechanism of palm oil waste pyrolysis in a packed bed,” Energy and Fuels, vol. 20, no. 3, pp. 1321–1328, 2006.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2017 Seyed Ali Zamani et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2768

Downloads

1474

Citations